Your PARTNER for HYGIENE and TECHNOLOGY

SAAoST
SAAoST
PHT SA
Tel: +27 861 777 993
Mail: info.za@pht.group
Hygiene
/ Hand Cleaning Basin

Hand cleaning basin

Personnel hygiene starts with cleaning hands.

Cleaning basin, type 20550

Cleaning basin type 20550

Cleaning basin, type 20550

This non-contact fitting is energy- and cost-efficient, hygienic and works only when needed. The water only flows when hands are placed under the stainless steel outlet, i.e. only when hands are actually being washed. This, combined with the use of a water-saving aerator, reduces water consumption to the one to one and a half litres that are actually required.

The cleaning basins also have an Aquaflow function which controls the stagnation times of the drinking water in the pipes, thus reducing the build-up of undesirable bacteria.

Cleaning of the forearms possible, in line with ASDA regulations.

Cleaning basin, type 20550, with non-contact operation and stainless steel soap dispenser (see left-hand picture below).

Cleaning basin, type 20550, with conical pedestal, sterilisation basin, type 2150, and paper towel dispenser with waste-paper basket (see centre picture below).

Cleaning basin, type 20550, with non-contact operation and soap and disinfection dispenser (see right-hand picture below).


Cleaning basin, type 20520

Cleaning basin type 20520 Cleaning basin type 20520

Cleaning basin, type 20520

Cleaning basin for mounting on the wall, pedestal or floor. Wrought basin body with rear panel made completely of type 1.4301 stainless steel and a hygienic surface with a roughness grade of Rz 04.

Cleaning basin, type 20520, with non-contact operation and plastic soap dispenser (see picture above).

Cleaning basin, type 20520, with knee-operated valve and plastic or stainless steel soap dispenser (see picture below).

Cleaning basin, type 20580 Clean and Dry

Cleaning basin type 20520 Cleaning basin type 20520 Cleaning basin type 20520 Cleaning basin type 20520

Cleaning basin, type 20580 Clean and Dry

Cleaning and drying hands at a stainless steel basin

With integrated hand drying technology from Dyson Airblade Tap, hands can be dried at the sink in just 12 seconds. A separate hand-drying area is unnecessary which prevents dripping onto floors and improves hygiene.

Water and air is supplied contactless – users do not need to touch the outlet. Intelligent infra-red sensors generate light to determine the precise positioning of hands. A highly effective HEPA filter removes
99.9 % of all air-borne bacteria and viruses before they reach the hands.

Contactless operation means water is consumed only when hands are held under the outlet. This reduces water consumption and operating costs.



• Hygienic design with a stainless steel rear panel and finely  finished hygienic surfaces. 

• The integrated Dyson AIRBLADE™ Tap, a sensor fitting with an integrated hand dryer, enables hand cleaning and drying directly at the basin in just 12 seconds.  

• No extra hand-drying space required and no splashes onto floor surfaces.

• Both water and air is controlled by a sensor so no contact is necessary to outlet fittings or control buttons.

• Water consumption is reduced significantly.

• Cleaning troughs with two and three Dyson AIRBLADE™ Tap also available.


Advantages: 


• 12-second drying time  
• A HEPA filter to remove 99.9 % of bacteria from the hand drying air 
• Low operating costs  HACCP certified  
• Low CO2 emissions  
• No splashes on floor surfaces  
• Non-contact operation  
• Reduces water consumption via sensor-controlled water flow 


Cleaning basin, Type 20260

Cleaning basin type 20520

Cleaning basin, Type 20260

With knee operated valve.

Cleaning basin, type 2041

Cleaning basin type 20520

Cleaning basin, type 2041

A particularly robust design for use in slaughterhouses. Pedestal model with stench trap and knife sterilisation basin, type 2150, mounted on the right-hand side and a plastic arm-operated soap dispenser with a capacity of 0.4 litres. The water is switched on via a knee-operated valve with a large surface.